With your consent, we analyze the use of our website with tracking technologies and cookies in order to optimize the website and improve it continuously. The consent is voluntary and can be revoked at any time. Further information can be found in our privacy policy.
English
Contact
E Series Valves and Manifolds
General Features
Needle Valves acc. to ISO 15848

Screwed Bonnet
– Type 1 O-Ring Stem Seal + Graphite Packing
   Type 3 PTFE Packing

Features

  • Integral Valve Seat – Metal to Metal Seated
  • Non-rotating Needle
  • External Stem Thread – Packing below stem threads. Stem Threads are protected from process media (non-wetted), helps to prevent stems from galling.
  • Stem with cold rolled threads
  • Back Seat – Metal to metal secondary needle seal
  • Color Coded Dust Cap for operating thread protection
  • Max. allowable (Working) Pressure (PS) 420 bar (6,092 psi)
  • Anti-Tamper Valve Head Options available
  • FKM O-Ring Needle Seal – RGD (Rapid Gas Decompression) resistant
  • PTFE or Graphite Packing
  • All non-wetted parts in 316 stainless steel
  • Types also comply with the requirements of TA-Luft 2002



ISO FE – Performance Data


ISO FE Type 1:
Class A 1,500 cycles / –29°C to 40°C
(–20°F to 104°F)
Class A    500 cycles / –29°C to 200°C
(–20°F to 392°F)
Class B 1,500 cycles / –29°C to 200°C
(–20°F to 392°F)

ISO FE Type 3:
Class B 1,500 cycles / –29°C to 200°C
(–20°F to 392°F)

OS&Y Needle Valve acc. to ISO 15848

QS&Y Bolted Bonnet
– Type 1 O-Ring Stem Seal + Graphite Packing
   Type 3 PTFE Packing

Features

  • Integral Valve Seat – Metal to Metal Seated
  • Non-rotating Needle
  • External Stem Thread – Packing below stem threads.
    Stem Threads are protected from process media (non-wetted),
    helps to prevent stems from galling.
  • Stem with cold rolled threads
  • Blow-out proof Needle
  • Spring Washers for compensation of thermal expansion
  • Back Seat – Metal to metal secondary stem seal
  • Color Coded Dust Cap for operating thread protection
  • Max. allowable (Working) Pressure (PS) 420 bar (6,092 psi)
  • Anti-Tamper Valve Head Options available
  • FKM O-Ring Stem Seal – RGD (Rapid Gas Decompression) resistant
  • PTFE or Graphite Packing
  • Bonnet Seal Ring: Graphite
  • All non-wetted parts in 316 stainless steel
  • Types also comply with the requirements of TA-Luft 2002



ISO FE – Performance Data


ISO FE Type 1:
Class A 1,500 cycles / –29°C to 40°C
(–20°F to 104°F)
Class A    500 cycles / –29°C to 200°C
(–20°F to 392°F)
Class B 2,500 cycles / –29°C to 200°C
(–20°F to 392°F)

ISO FE Type 3:
Class B 2,500 cycles / –29°C to 200°C
(–20°F to 392°F)

Bellows Sealed Head Units
Screwed Bonnet
– PN 100 and Graphite Safety Packing
   PN 250 and Graphite Safety Packing

Features

  • Integral Valve Seat – Metal to Metal Seated
  • Non-rotating Stem
  • Bellows sealed – PN 100 and PN 250 incl. Graphite Safety Packing
  • Stem with cold rolled threads
  • Stellite Needle Tip as standard
  • Bellows are submitted to a 100% Helium leak test
  • Leak rate: 10-8 mbar l/s
  • Valves for Oxygen Service on request

Bellows Sealed Head Units are mainly used for applications requiring the highest tightness class – such as toxic or vacuum service.

Attention:
Packing adjustment may be required during the service life of
the valves. Valves that have not been cycled for a period of
time may have a higher initial actuation torque. When delivered
ex factory, the safety packing of the belllows sealed valve is not
fully tightened. In the event of a bellows failure the safety packing
must be tightened in order to avoid fluid leakage.

Copyright © 2015 Armaturenfabrik Franz Schneider GmbH + Co. KG. All rights reserved.